QPO300 - Polyester Chemical anchors
Two-component polyester-based injection adhesive fastening system for medium and light loads in concrete and masonry.
FEATURES AND ADVANTAGES
- Anchoring for medium and light loads in concrete and masonry.
- Clean, agile and simple application with standard manual applicator (300 ml).
- Dry, wet and submerged concrete installations.
- Applicable for dynamic loads.
- Styrene-free and with a fast curing system.
- Thixotropic: does not run.
- Anchoring in hollow masonry (requires the use of a jacket).
- VMC system: better control during installation; changes color after curing.
- It has international technical approvals (ETA).
STORAGE CONDITIONS
Store in a cool, dry place at a temperature below 25ºC. Do not expose the product to the sun. Provided it is stored in ideal conditions, it has a shelf life of 15 months after the date of manufacture."
CERTIFICATIONS
- ETA opção 7: Ancoragem de barras roscadas em concreto não fissurado.
- ETA - ETAG 029 : Fastening in masonry elements.
- VOC A+.
- LEED.
MAIN APPLICATIONS
- Installation of gates
- Installation of awnings and guardrails
- Fastening light metal structures and parts
- Installing threaded rods in masonry
Concrete
Concrete block
Ceramic block
Structural Block
Solid brick
Stone
APPLICATION METHOD
Threaded rod on solid base.
Step: 1/6
Drill the hole as indicated.
Step: 2/6
Clean the hole with
brush and air.
brush and air.
Step: 3/6
Pull the seal and cut the bag.
Step: 4/6
Screw in the mixing nozzle.
Step: 5/6
Place the cartridge in the APL300 applicator.
Step: 6/6
Dispense the beginning of the resin until a homogeneous mixture is obtained.
Threaded rod on solid base
Step: 1/4
Apply the resin to the hole. Fill 2/3 of the hole from the bottom to the surface
Step: 2/4
Insert the rod by turning it.
Step: 3/4
Wait for the curing time.
Step: 4/4
Position the part and finish fixing.
Threaded rod in hollow base
Step: 1/5
Insert the sleeve into the hole.
Step: 2/5
Inject the resin into the jacket until it fills it.
Step: 3/5
Insert the retaining cap into the jacket by bending it
Step: 4/5
Insert the rod by turning it.
Step: 5/5
Wait for the curing time, position the piece and finish fixing.
VIDEO
| Physical properties | Density of 1.7/styrene-free thixotropic (does not run off). |
|---|---|
| Packaging | 300 ml cartridges |
| Applicator | APL300 |
| Working and curing time | |||||
|---|---|---|---|---|---|
| Base material temperature | +5°C to +10°C |
+10°C to +20°C |
+20°C to +25°C |
+25°C to +30°C |
+30°C |
| Working time¹ | 10 min. | 6 min. | 5 min. | 4 min. | 4 min. |
| Curing time² | 2h25 min. | 1h25 min. | 50 min. | 40 min. | 35 min. |
SOLID CONCRETE BASE - THREADED ROD
| Diameter | Hole (mm) | Distance³ (mm) | Wrench (inch) | Torque4 (kgf.m) | Fixings by cartridge5 | Ultimate loads² (kgf) | ||||
|---|---|---|---|---|---|---|---|---|---|---|
| (in.) | (mm) | Diameter | Depth¹ | Fastener fastener | Edge fastener | Tensile | Shear | |||
| 5/16" | 8 | 10 | 80 | 160 | 80 | 1/2" | 1,5 | 68 | 1.951 | 1.887 |
| 3/8" | 10 | 12 | 90 | 180 | 90 | 9/16" | 2 | 43 | 2.583 | 2.768 |
| 1/2" | 12 | 14 | 110 | 220 | 110 | 3/4" | 4,1 | 36 | 4.262 | 4.924 |
| 5/8" | 16 | 18 | 128 | 256 | 128 | 15/16" | 8,2 | 19 | 6.614 | 8.017 |
| 3/4" | 20 | 22 | 170 | 340 | 170 | 1.1/8″ | 15,3 | 9 | 9.759 | 11.818 |
| 1” | 24 | 28 | 210 | 420 | 210 | 1.1/2″ | 22,4 | 5 | 13.562 | 21.304 |
¹Standard depth. ²The values obtained are based on the average of tests and technical specifications, using ASTM A193B7 rod and 30 MPa concrete. Please note: these values are ultimate loads; always use the safety coefficient. Recommended minimum distance. For shorter distances, consult the Technical Department. 4Values valid for ASTM 193 B7 rods / ASTM A194 2H nuts. 5Estimated values under ideal conditions of use.
HOLLOW BASES - THREADED ROD
CONCRETE BLOCK
| Threaded rod | Sleeve | Hole | Minimum recommended distance² (mm) | Wrench (inch) | Torque³ (kgf.m) | Fixings by cartridge4 | Ultimate loads¹ (kgf) | |||
|---|---|---|---|---|---|---|---|---|---|---|
| Diameter (mm) | Minimum depth | Fastener fastener | Edge fastener | Tensile | Shear | |||||
| 1/4" | 12 x 50 CAM12050 | 12 | 55 | 1 block | 1/2 block | 7/16" | 0,3 | 42 | 300 | 280 |
| 5/16" | 1/2" | 0,4 | 400 | 360 | ||||||
| 3/8" | 16 x 85 CAM15080 | 16 | 90 | 9/16" | 0,4 | 16 | 500 | 360 | ||
| 3/8" | 16 x 130 CAM15130 | 16 | 135 | 9/16" | 0,4 | 10 | 700 | 360 | ||
| 1/2" | 20 x 85 CAM2085 | 20 | 90 | 3/4" | 0,6 | 8 | 700 | 360 | ||
HOLLOW BASES - THREADED ROD
CERAMIC BLOCK
| Threaded rod | Sleeve | Hole | Minimum recommended distance² (mm) | Wrench (inch) | Torque³ (kgf.m) | Fixings by cartridge4 | Ultimate loads¹ (kgf) | |||
|---|---|---|---|---|---|---|---|---|---|---|
| Diameter (mm) | Minimum depth | Fastener fastener | Edge fastener | Tensile | Shear | |||||
| 1/4" | 12 x 50 CAM12050 | 12 | 55 | 1 block | 1/2 block | 7/16" | 0,3 | 42 | 300 | 280 |
| 5/16" | 1/2" | 0,4 | 370 | 360 | ||||||
| 3/8" | 16 x 85 CAM15080 | 16 | 90 | 9/16" | 0,4 | 16 | 460 | 360 | ||
| 3/8" | 16 x 130 CAM15130 | 16 | 135 | 9/16" | 0,4 | 10 | 610 | 360 | ||
| 1/2" | 20 x 85 CAM2085 | 20 | 90 | 3/4" | 0,6 | 8 | 610 | 360 | ||
(1) The values obtained are based on the average of tests and technical specifications, using an ABNT 1010/1020 rod in a concrete/ceramic block, with a 2 cm
coating. Please note: these values are ultimate loads, always use the safety coefficient. For more information, see the Technical Data section on page 135.
(2) Recommended minimum distance, for smaller distances consult the technical department. (3) Values valid for ABNT 1010/1020 rods.
(4) Estimated values under ideal conditions of use.
coating. Please note: these values are ultimate loads, always use the safety coefficient. For more information, see the Technical Data section on page 135.
(2) Recommended minimum distance, for smaller distances consult the technical department. (3) Values valid for ABNT 1010/1020 rods.
(4) Estimated values under ideal conditions of use.
